sign in   register   cart (0)   favorite () 
  Home > How to Hang

VINYL WALLCOVERING SURFACE PREPARATION

All wall surfaces should be structurally sound. Sand finished plaster should be smoothed.
In order to insure good adhesion, old wallcovering and loose paint flakes should be removed.
All wall surfaces should be primed with a suitable acrylic primer.

Do not hang vinyl over ballpoint pen writing, wax crayon, wick pen markings, or foreign matter that may be on the wall. 
These impurities  may bleed through the vinyl even a year after installation. It is  suggested that lead pencils be used to 
mark vinyl or walls as the use of  a pencil should not produce bleed through after effects.

In order to insure maximum smoothness of installation, nail heads, nicks, gouges and other surface imperfections should be 
sanded smooth and  sealed. On new walls, dry wall joints should be taped, bedded and sanded  smooth.

One of the characteristics of vinyl wallcovering is that it has little or no moisture permeability. This characteristic can be  
an important benefit in terms of cleanability and wall protection and in  limiting interior moisture (e.g. bathrooms) from 
entering the wall  cavity. However, if the design, construction or maintenance of a  building, or other circumstances allows 
liquid or vapor moisture to  accumulate in a wall or wall cavity, vinyl wallcovering can act as a  vapor barrier restricting the 
escape of moisture and increasing the risk  of mold growth.
Buildings that have moisture infiltration problems are at risk for mold and mildew growth and any such problems must be  
corrected prior to the installation of vinyl wallcovering.

This product is intended for use in buildings that are properly designed and maintained to avoid moisture infiltration, 
condensation and/or  accumulation at wall cavities and wall surfaces, particularly in warm,  humid climates.

ADHESIVE

A premium quality premixed full strength vinyl adhesive should be applied to the fabric side of the wallcovering 
rather than the wall. Do  not dilute paste. The adhesive should be stored at room temperature  (70°F).

APPLICATION

1. Store the wallcovering in a clean, dry and protected environment. Maintain for 72 hours at not less than 70°F 
(but less than  l00°F) prior to and during the installation.

2. Before cutting, be sure the pattern and color are satisfactory as specified.

3. Before hanging, examine pattern for color uniformity and repeat in design. If there is no design repeat 
(random texture) patterns should  normally be reverse hung.

4. All material must be installed in numerical roll sequence starting with the highest number.

5. IF, AFTER APPLYING THREE (3) STRIPS, THERE IS SOME QUESTION OF APPEARANCE, 
STOP AND CONTACT YOUR LOCAL REPRESENTATIVE.

6. Apply an even coat of adhesive to the fabric side of material using a roller or pasting machine. 
The wallcovering should be booked for  a minimum of 15 minutes. When pasting several strips in advance,  
booking is recommended to insure proper wetting out of the fibers and to  prevent drying out of paste on the edges. 
Install wall covering using a  plastic smoother, working out air bubbles.

Caution: REMOVE EXCESS PASTE IMMEDIATELY WITH CLEAN WARM WATER AND A MOIST NATURAL SPONGE.
DO NOT USE MAN MADE (i.e. POLYESTER) SPONGES. DRY WITH A CLEAN CLOTH.
IF EXCESS PASTE IS NOT REMOVED PERMANENT DAMAGE COULD RESULT TO THE FACE OF THE VINYL.


7. Only full widths of material should be used for the most satisfactory installation. Headers can cause unsatisfactory 
shading if  hung out of sequence; as with all vinyl wallcoverings, certain deeply  embossed patterns will provide a more 
satisfactory seam if a selvage cut  is taken from each side of the sheet ("double cut"). Do not "score" the  dry wall.

8. Wall surface should be smooth, clean, dry, structurally sound, free of mold, mildew, grease or stains, and undamaged.

9. Before installation, verify that wall moisture content does not exceed 4% (using a suitable moisture meter) and that 
active moisture or  water vapor infiltration is not present.

10. Before installation, verify that walls are free from mold and mildew. If mold or mildew is present, or if walls show 
visible moisture  damage, or if moisture content exceeds recommendations, do not proceed  with installation until the 
condition has been fully corrected under the  direction of a qualified expert. Moisture in and behind the wall must  be 
eliminated. Depending upon the severity of the damage, mold or mildew  in many cases may be removed by washing 
the walls with warm, soapy  water and/or treating: with a diluted bleach solution. Walls then must  be fully dried prior to 
application of wallcovering. Application of  mildew inhibiting primer products is recommended. However severe or  persistent 
mold or mildew conditions require professional evaluation and  remediation.

11. After installation, the walls and wallcovering should be monitored for potential moisture or vapor infiltration. Any such  
infiltration after installation must be promptly eliminated.

12. Use of a mildew inhibitor in the adhesive is recommended.

WALLCOVERING MAINTENANCE

Listed below (in the preferred order of use) are the solutions that can be used for cleaning.

1. Clear warm water.

2. Mild soapy warm water, then rinse.

3. Do not use solvent based cleaning agents, lacquer thinners, nail polish remover, pine oil or cleaning agents containing 
bleach,  which may cause discoloration over a period of time.

4. It is recommended that cleaning be done with a natural sponge. A cloth or towel should only be used to tamp dry (not rub). 
Do not use  manmade (i.e. polyester) sponges.



 
COSMOS Wallpaper, Corp. Copyright (c) All Rights Reserved